Manufacturing method of optical film storage device for medical imaging department

1 storage box, 2 adjustment rods, 3 timing belts, 4 rotating rods, 5 telescopic rods, 6 top plates, 7 storage compartments, 8 guide rods, 9 connecting blocks, 10 fixing plates, 11 sets of rods, 12 force springs, 13 Rod, 14 splints.

detailed description

21. The following will clearly and completely describe the technical solutions in the embodiments of the present utility model in conjunction with the accompanying drawings in the embodiments of the present utility model. Obviously, the described embodiments are only a part of the embodiments of the present utility model, not all of them.的实施例。 Example.

22. Refer to Figure 

4. Optical film storage device for medical imaging department, including storage box 1. The bottom inner side of storage box 1 is connected with two parallel adjustment rods 2 through bearings, and the bottom inner side of storage box 1 is also connected with four vertical settings through bearings. The top outside of the rotating rod 4 is sleeved with a telescopic rod 5 extending to the outside of the top of the storage box 1, and the top plate 6 is fixed by bolts of the telescopic rod 5;

23. The bottom of the top plate 6 is equipped with a storage compartment 7, the inside of the top plate 6 is installed with guide rods 8 evenly distributed through bearings, and the outside of the guide rod 8 is sleeved with a connecting block 9, which is bolted to the storage compartment through the connecting block 9 7 is the fixed plate 10, the inner wall of the fixed plate 10 is provided with a sleeve rod 11, the inner wall of the sleeve rod 11 is respectively provided with a force spring 12 and a support rod 13 extending to the outside of the end of the sleeve rod 11, which is connected by the support rod 13 There is a splint 14;

24. The outer parts of the two adjusting rods 2 are sleeved with timing belt wheels, and the timing belt 3 is wound around the outside of the timing belt wheels. Both ends of the rod 2 are sleeved with driving gears, the bottom outside of the rotating rod 4 is sleeved with a transmission gear meshing with the driving gear, the surface of the rotating rod 4 is provided with threads, and the inner wall of the telescopic rod 5 is provided with threads corresponding to its surface The surface of the guide rod 8 is provided with a thread, the inner wall of the connecting block 9 is provided with a thread groove corresponding to the thread on the surface, and the ends of the two clamping plates 14 are arc-shaped and expanded outward.

25. In this embodiment, two adjusting rods 2 are connected to the inner bearing of the bottom of the storage box 1, which are synchronously driven by a timing belt 3, and the driving gear and transmission gear are used to drive the four rotating rods 4 to rotate synchronously, and the rotating rod 4 rotates. The telescopic rod 5 screwed on the top is driven to push the top plate 6 up and down, which facilitates the access operation of the light sheet, the structure is simple, and the operation is convenient.

26. Further, a storage compartment 7 is provided at the bottom of the top plate 6, and a guide rod 8 is connected to the bearing inside the top plate 6. Rotating the guide rod 8 can drive its external threaded connection block 9 to push the fixed plate 10 to drive under the top plate 6. In this way, the light sheet fixed inside it is led out and stored.

27. Among them, the inner wall of the fixed plate 10 is welded to the sleeve rod 11, and the clamping plate 14 at the end of the support rod 13 is clamped and fixed by the force spring 12 in the sleeve rod 11, which has good stability and can hold each light The slices are separated, not easy to confuse, convenient to take, and improve the work efficiency of medical workers.

28. The above are only the preferred specific embodiments of the present utility model, but the scope of protection of the present utility model is not limited to this. Anyone familiar with the technical field in the technical scope disclosed by the present utility model, according to The technical scheme of the utility model and the concept of the utility model are equivalently replaced or changed, and all shall be covered within the protection scope of the utility model.

Please contact us at zhang@pride-cnc.com